Print settings

Job Name	CE3_DokkalfQueen
Date	25/05/2021 13:57:38
Os	Windows 10.0.16299
Cura Version	4.9.1
Profile	PLA+ Grigio ULTRA
Quality	Standard Quality
Material Extruder : 1	PLA
Material estimation	6.8 g
Printing Time	0 d 3 h 37 mn
Extruder : 1 Quality
Layer Height	0.1	mm
Initial Layer Height	0.2	mm
Line Width	0.4	mm
Wall Line Width	0.4	mm
Outer Wall Line Width	0.4	mm
Inner Wall(s) Line Width	0.4	mm
Top/Bottom Line Width	0.4	mm
Infill Line Width	0.4	mm
Skirt/Brim Line Width	0.4	mm
Support Line Width	0.4	mm
Support Interface Line Width	0.4	mm
Support Roof Line Width	0.4	mm
Support Floor Line Width	0.4	mm
Prime Tower Line Width	0.4	mm
Initial Layer Line Width	120	%
Extruder : 1 Walls
Wall Extruder	-1
Outer Wall Extruder	-1
Inner Wall Extruder	-1
Wall Thickness	0.8	mm
Wall Line Count	2
Outer Wall Wipe Distance	0.4	mm
Outer Wall Inset	0	mm
Optimize Wall Printing Order	True
Outer Before Inner Walls	False
Alternate Extra Wall	False
Compensate Wall Overlaps	True
Compensate Outer Wall Overlaps	False
Compensate Inner Wall Overlaps	True
Minimum Wall Flow	0	%
Prefer Retract	False
Fill Gaps Between Walls	Everywhere
Filter Out Tiny Gaps	False
Print Thin Walls	False
Horizontal Expansion	0	mm
Initial Layer Horizontal Expansion	0	mm
Hole Horizontal Expansion	0	mm
Z Seam Alignment	User Specified
Z Seam Position	Back
Z Seam X	0	mm
Z Seam Y	500	mm
Seam Corner Preference	Smart Hiding
Z Seam Relative	False	mm
Extruder : 1 Top/Bottom
Top Surface Skin Extruder	-1
Top Surface Skin Layers	1
Top/Bottom Extruder	-1
Top/Bottom Thickness	0.5	mm
Top Thickness	0.5	mm
Top Layers	5
Bottom Thickness	0.5	mm
Bottom Layers	4
Initial Bottom Layers	4
Top/Bottom Pattern	Lines
Bottom Pattern Initial Layer	Lines
Connect Top/Bottom Polygons	False
Top/Bottom Line Directions	[ ]
No Skin in Z Gaps	True
Extra Skin Wall Count	1
Enable Ironing	False
Iron Only Highest Layer	False
Ironing Pattern	Concentric
Ironing Line Spacing	0.1	mm
Ironing Flow	20	%
Ironing Inset	0.06	mm
Ironing Speed	13.3333	mm/s
Ironing Acceleration	500	mm/s²
Ironing Jerk	8	mm/s
Skin Overlap Percentage	10	%
Skin Overlap	0.04	mm
Skin Removal Width	0.8	mm
Top Skin Removal Width	0.8	mm
Bottom Skin Removal Width	0.8	mm
Skin Expand Distance	0.8	mm
Top Skin Expand Distance	0.8	mm
Bottom Skin Expand Distance	0.8	mm
Maximum Skin Angle for Expansion	90	°
Minimum Skin Width for Expansion	0	mm
Extruder : 1 Infill
Infill Extruder	-1
Infill Density	15	%
Infill Line Distance	5.3333	mm
Infill Pattern	Grid
Connect Infill Lines	False
Connect Infill Polygons	False
Infill Line Directions	[ ]
Infill X Offset	0	mm
Infill Y Offset	0	mm
Randomize Infill Start	False
Infill Line Multiplier	1
Extra Infill Wall Count	0
Cubic Subdivision Shell	0.4	mm
Infill Overlap Percentage	15	%
Infill Overlap	0.06	mm
Infill Wipe Distance	0.04	mm
Infill Layer Thickness	0.1	mm
Gradual Infill Steps	0
Gradual Infill Step Height	1.5	mm
Infill Before Walls	False
Minimum Infill Area	0	mm²
Infill Support	False
Infill Overhang Angle	40	°
Skin Edge Support Thickness	0	mm
Skin Edge Support Layers	0
Extruder : 1 Material
Default Printing Temperature	200	°C
Build Volume Temperature	28	°C
Printing Temperature	214	°C
Printing Temperature Initial Layer	217	°C
Initial Printing Temperature	217	°C
Final Printing Temperature	214	°C
Extrusion Cool Down Speed Modifier	0.7	°C/s
Default Build Plate Temperature	50	°C
Build Plate Temperature	55	°C
Build Plate Temperature Initial Layer	60	°C
Adhesion Tendency	0
Surface Energy	100	%
Scaling Factor Shrinkage Compensation	100	%
Crystalline Material	False
Anti-ooze Retracted Position	-4	mm
Anti-ooze Retraction Speed	5	mm/s
Break Preparation Retracted Position	-16	mm
Break Preparation Retraction Speed	2	mm/s
Break Preparation Temperature	214	°C
Break Retracted Position	-50	mm
Break Retraction Speed	25	mm/s
Break Temperature	50	°C
Flush Purge Speed	0.5
Flush Purge Length	60
End of Filament Purge Speed	0.5
End of Filament Purge Length	20
Maximum Park Duration	300
No Load Move Factor	0.9409
Flow	94	%
Wall Flow	94	%
Outer Wall Flow	94	%
Inner Wall(s) Flow	94	%
Top/Bottom Flow	94	%
Top Surface Skin Flow	94	%
Infill Flow	94	%
Skirt/Brim Flow	94	%
Support Flow	94	%
Support Interface Flow	94	%
Support Roof Flow	94	%
Support Floor Flow	94	%
Prime Tower Flow	94	%
Initial Layer Flow	120	%
Standby Temperature	180	°C
Extruder : 1 Speed
Print Speed	40	mm/s
Infill Speed	30	mm/s
Wall Speed	25	mm/s
Outer Wall Speed	20	mm/s
Inner Wall Speed	25	mm/s
Top Surface Skin Speed	20	mm/s
Top/Bottom Speed	20	mm/s
Support Speed	35	mm/s
Support Infill Speed	35	mm/s
Support Interface Speed	20	mm/s
Support Roof Speed	20	mm/s
Support Floor Speed	20	mm/s
Prime Tower Speed	20	mm/s
Travel Speed	200	mm/s
Initial Layer Speed	20	mm/s
Initial Layer Print Speed	20	mm/s
Initial Layer Travel Speed	100	mm/s
Skirt/Brim Speed	30	mm/s
Z Hop Speed	5	mm/s
Number of Slower Layers	2
Equalize Filament Flow	False
Maximum Speed for Flow Equalization	150	mm/s
Enable Acceleration Control	False
Print Acceleration	500	mm/s²
Infill Acceleration	500	mm/s²
Wall Acceleration	500	mm/s²
Outer Wall Acceleration	500	mm/s²
Inner Wall Acceleration	500	mm/s²
Top Surface Skin Acceleration	500	mm/s²
Top/Bottom Acceleration	500	mm/s²
Support Acceleration	500	mm/s²
Support Infill Acceleration	500	mm/s²
Support Interface Acceleration	500	mm/s²
Support Roof Acceleration	500	mm/s²
Support Floor Acceleration	500	mm/s²
Prime Tower Acceleration	500	mm/s²
Travel Acceleration	500	mm/s²
Initial Layer Acceleration	500	mm/s²
Initial Layer Print Acceleration	500	mm/s²
Initial Layer Travel Acceleration	500	mm/s²
Skirt/Brim Acceleration	500	mm/s²
Enable Jerk Control	False
Print Jerk	8	mm/s
Infill Jerk	8	mm/s
Wall Jerk	8	mm/s
Outer Wall Jerk	8	mm/s
Inner Wall Jerk	8	mm/s
Top Surface Skin Jerk	8	mm/s
Top/Bottom Jerk	8	mm/s
Support Jerk	8	mm/s
Support Infill Jerk	8	mm/s
Support Interface Jerk	8	mm/s
Support Roof Jerk	8	mm/s
Support Floor Jerk	8	mm/s
Prime Tower Jerk	8	mm/s
Travel Jerk	8	mm/s
Initial Layer Jerk	8	mm/s
Initial Layer Print Jerk	8	mm/s
Initial Layer Travel Jerk	8	mm/s
Skirt/Brim Jerk	8	mm/s
Extruder : 1 Travel
Enable Retraction	True
Retract at Layer Change	True
Retraction Distance	5.3	mm
Retraction Speed	50	mm/s
Retraction Retract Speed	50	mm/s
Retraction Prime Speed	50	mm/s
Retraction Extra Prime Amount	0	mm³
Retraction Minimum Travel	1	mm
Maximum Retraction Count	10
Minimum Extrusion Distance Window	8	mm
Limit Support Retractions	True
Combing Mode	Within Infill
Max Comb Distance With No Retract	30	mm
Retract Before Outer Wall	True
Avoid Printed Parts When Traveling	True
Avoid Supports When Traveling	False
Travel Avoid Distance	0.625	mm
Layer Start X	0	mm
Layer Start Y	0	mm
Z Hop When Retracted	True
Z Hop Only Over Printed Parts	True
Z Hop Height	0.5	mm
Z Hop After Extruder Switch	True
Z Hop After Extruder Switch Height	0.5	mm
Extruder : 1 Cooling
Enable Print Cooling	True
Fan Speed	100	%
Regular Fan Speed	100	%
Maximum Fan Speed	100	%
Regular/Maximum Fan Speed Threshold	10	s
Initial Fan Speed	0	%
Regular Fan Speed at Height	0.4	mm
Regular Fan Speed at Layer	4
Minimum Layer Time	10	s
Minimum Speed	10	mm/s
Lift Head	False
Support
Generate Support	False
Support Extruder	0
Support Infill Extruder	0
First Layer Support Extruder	0
Support Interface Extruder	0
Support Roof Extruder	0
Support Floor Extruder	0
Support Structure	Normal
Tree Support Branch Angle	40	°
Tree Support Branch Distance	1	mm
Tree Support Branch Diameter	2	mm
Tree Support Branch Diameter Angle	5	°
Tree Support Collision Resolution	0.2	mm
Support Placement	Touching Buildplate
Support Overhang Angle	63	°
Support Pattern	Lines
Support Wall Line Count	1
Connect Support Lines	False
Connect Support ZigZags	True
Support Density	25	%
Support Line Distance	1.6	mm
Initial Layer Support Line Distance	1.6	mm
Support Infill Line Directions	[ ]
Enable Support Brim	True
Support Brim Width	4	mm
Support Brim Line Count	11
Support Z Distance	0.2	mm
Support Top Distance	0.2	mm
Support Bottom Distance	0	mm
Support X/Y Distance	0.8	mm
Support Distance Priority	X/Y overrides Z
Minimum Support X/Y Distance	0.4	mm
Support Stair Step Height	0.3	mm
Support Stair Step Maximum Width	5	mm
Support Stair Step Minimum Slope Angle	10	°
Support Join Distance	2	mm
Support Horizontal Expansion	0	mm
Support Infill Layer Thickness	0.1	mm
Gradual Support Infill Steps	0
Gradual Support Infill Step Height	1	mm
Minimum Support Area	2	mm²
Enable Support Interface	True
Enable Support Roof	True
Enable Support Floor	True
Support Interface Thickness	0.4	mm
Support Roof Thickness	0.4	mm
Support Floor Thickness	0.4	mm
Support Interface Resolution	0.2	mm
Support Interface Density	33.333	%
Support Roof Density	33.333	%
Support Roof Line Distance	2.4	mm
Support Floor Density	33.333	%
Support Floor Line Distance	2.4	mm
Support Interface Pattern	Grid
Support Roof Pattern	Grid
Support Floor Pattern	Grid
Minimum Support Interface Area	10	mm²
Minimum Support Roof Area	10	mm²
Minimum Support Floor Area	10	mm²
Support Interface Horizontal Expansion	0	mm
Support Roof Horizontal Expansion	0	mm
Support Floor Horizontal Expansion	0	mm
Support Interface Line Directions	[ ]
Support Roof Line Directions	[ ]
Support Floor Line Directions	[ ]
Fan Speed Override	False
Supported Skin Fan Speed	100	%
Use Towers	False
Tower Diameter	3	mm
Maximum Tower-Supported Diameter	3	mm
Tower Roof Angle	65	°
Drop Down Support Mesh	True
Scene Has Support Meshes	False
Build Plate Adhesion
Enable Prime Blob	False
Extruder Prime X Position	0	mm
Extruder Prime Y Position	0	mm
Build Plate Adhesion Type	Brim
Build Plate Adhesion Extruder	0
Skirt Line Count	3
Skirt Distance	10	mm
Skirt/Brim Minimum Length	250	mm
Brim Width	8	mm
Brim Line Count	17
Brim Distance	0	mm
Brim Replaces Support	False
Brim Only on Outside	True
Raft Extra Margin	15	mm
Raft Smoothing	5	mm
Raft Air Gap	0.3	mm
Initial Layer Z Overlap	0.15	mm
Raft Top Layers	2
Raft Top Layer Thickness	0.1	mm
Raft Top Line Width	0.4	mm
Raft Top Spacing	0.4	mm
Raft Middle Thickness	0.15	mm
Raft Middle Line Width	0.8	mm
Raft Middle Spacing	1	mm
Raft Base Thickness	0.24	mm
Raft Base Line Width	0.8	mm
Raft Base Line Spacing	1.6	mm
Raft Print Speed	20	mm/s
Raft Top Print Speed	20	mm/s
Raft Middle Print Speed	15	mm/s
Raft Base Print Speed	15	mm/s
Raft Print Acceleration	500	mm/s²
Raft Top Print Acceleration	500	mm/s²
Raft Middle Print Acceleration	500	mm/s²
Raft Base Print Acceleration	500	mm/s²
Raft Print Jerk	8	mm/s
Raft Top Print Jerk	8	mm/s
Raft Middle Print Jerk	8	mm/s
Raft Base Print Jerk	8	mm/s
Raft Fan Speed	0	%
Raft Top Fan Speed	0	%
Raft Middle Fan Speed	0	%
Raft Base Fan Speed	0	%
Extruder : 1 Mesh Fixes
Union Overlapping Volumes	True
Remove All Holes	False
Extensive Stitching	False
Keep Disconnected Faces	False
Merged Meshes Overlap	0.15	mm
Remove Mesh Intersection	False
Alternate Mesh Removal	True
Remove Empty First Layers	True
Maximum Resolution	0.25	mm
Maximum Travel Resolution	0.25	mm
Maximum Deviation	0.025	mm
Special Modes
Print Sequence	All at Once
Infill Mesh	False
Mesh Processing Rank	0
Cutting Mesh	False
Mold	False
Minimal Mold Width	5	mm
Mold Roof Height	0.5	mm
Mold Angle	40	°
Support Mesh	False
Anti Overhang Mesh	False
Surface Mode	Normal
Spiralize Outer Contour	False
Smooth Spiralized Contours	True
Relative Extrusion	False
Experimental
Slicing Tolerance	Middle
Top Surface Skin Line Width	0.4	mm
Top Surface Skin Pattern	Lines
Top Surface Skin Line Directions	[ ]
Infill Travel Optimization	False
Auto Temperature	False
Flow Temperature Graph	[[3.5,200],[7.0,240]]	[[mm³,°C]]
Minimum Polygon Circumference	1	mm
Break Up Support In Chunks	False
Support Chunk Size	20	mm
Support Chunk Line Count	12
Enable Draft Shield	False
Draft Shield X/Y Distance	10	mm
Draft Shield Limitation	Full
Draft Shield Height	10	mm
Make Overhang Printable	False
Maximum Model Angle	50	°
Maximum Overhang Hole Area	0	mm²
Enable Coasting	True
Coasting Volume	0.08	mm³
Minimum Volume Before Coasting	0.8	mm³
Coasting Speed	90	%
Cross 3D Pocket Size	5.3333	mm
Cross Infill Density Image
Cross Fill Density Image for Support
Enable Conical Support	False
Conical Support Angle	30	°
Conical Support Minimum Width	5	mm
Fuzzy Skin	False
Fuzzy Skin Outside Only	False
Fuzzy Skin Thickness	0.3	mm
Fuzzy Skin Density	1.25	1/mm
Fuzzy Skin Point Distance	0.8	mm
Flow Rate Compensation Max Extrusion Offset	0	mm
Flow Rate Compensation Factor	100	%
Wire Printing	False
WP Connection Height	3	mm
WP Roof Inset Distance	3	mm
WP Speed	5	mm/s
WP Bottom Printing Speed	5	mm/s
WP Upward Printing Speed	5	mm/s
WP Downward Printing Speed	5	mm/s
WP Horizontal Printing Speed	5	mm/s
WP Flow	100	%
WP Connection Flow	100	%
WP Flat Flow	100	%
WP Top Delay	0	s
WP Bottom Delay	0	s
WP Flat Delay	0.1	s
WP Ease Upward	0.3	mm
WP Knot Size	0.6	mm
WP Fall Down	0.5	mm
WP Drag Along	0.6	mm
WP Strategy	Compensate
WP Straighten Downward Lines	20	%
WP Roof Fall Down	2	mm
WP Roof Drag Along	0.8	mm
WP Roof Outer Delay	0.2	s
WP Nozzle Clearance	1	mm
Use Adaptive Layers	False
Adaptive Layers Maximum Variation	0.04	mm
Adaptive Layers Variation Step Size	0.04	mm
Adaptive Layers Topography Size	0.2	mm
Overhanging Wall Angle	90	°
Overhanging Wall Speed	100	%
Enable Bridge Settings	False
Minimum Bridge Wall Length	5	mm
Bridge Skin Support Threshold	50	%
Bridge Sparse Infill Max Density	0	%
Bridge Wall Coasting	100	%
Bridge Wall Speed	10	mm/s
Bridge Wall Flow	50	%
Bridge Skin Speed	10	mm/s
Bridge Skin Flow	60	%
Bridge Skin Density	100	%
Bridge Fan Speed	100	%
Bridge Has Multiple Layers	True
Bridge Second Skin Speed	10	mm/s
Bridge Second Skin Flow	100	%
Bridge Second Skin Density	75	%
Bridge Second Skin Fan Speed	0	%
Bridge Third Skin Speed	10	mm/s
Bridge Third Skin Flow	110	%
Bridge Third Skin Density	80	%
Bridge Third Skin Fan Speed	0	%
Wipe Nozzle Between Layers	True
Material Volume Between Wipes	10	mm³
Wipe Retraction Enable	True
Wipe Retraction Distance	5.3	mm
Wipe Retraction Extra Prime Amount	0	mm³
Wipe Retraction Speed	50	mm/s
Wipe Retraction Retract Speed	50	mm/s
Wipe Retraction Prime Speed	50	mm/s
Wipe Pause	0	s
Wipe Z Hop	True
Wipe Z Hop Height	0.5	mm
Wipe Hop Speed	5	mm/s
Wipe Brush X Position	100	mm
Wipe Repeat Count	5
Wipe Move Distance	20	mm
Small Hole Max Size	0	mm
Small Feature Max Length	0	mm
Small Feature Speed	50	%
Small Feature Initial Layer Speed	50	%
Machine
Machine Type	Creality Ender-3
Show Machine Variants	False
Start G-code	; Ender 3 Custom Start G-code G92 E0 ; Reset Extruder G28 ; Home all axes G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X0.1 Y20 Z0.3 F5000.0 ; Move to start position G1 X0.1 Y200.0 Z0.3 F1500.0 E15 ; Draw the first line G1 X0.4 Y200.0 Z0.3 F5000.0 ; Move to side a little G1 X0.4 Y20 Z0.3 F1500.0 E30 ; Draw the second line G92 E0 ; Reset Extruder G1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed G1 X5 Y20 Z0.3 F5000.0 ; Move over to prevent blob squish
End G-code	G91 ;Relative positioning G1 E-2 F2700 ;Retract a bit G1 E-2 Z0.2 F2400 ;Retract and raise Z G1 X5 Y5 F3000 ;Wipe out G1 Z10 ;Raise Z more G90 ;Absolute positioning G1 X0 Y{machine_depth} ;Present print M106 S0 ;Turn-off fan M104 S0 ;Turn-off hotend M140 S0 ;Turn-off bed M84 X Y E ;Disable all steppers but Z
Material GUID	0ff92885-617b-4144-a03c-9989872454bc
Diameter	1.75	mm
Wait for Build Plate Heatup	True
Wait for Nozzle Heatup	True
Include Material Temperatures	True
Include Build Plate Temperature	True
Machine Width	235
Machine Depth	235
Build Plate Shape	Rectangular
Build Plate Material	Glass
Machine Height	250
Has Heated Build Plate	True
Has Build Volume Temperature Stabilization	False
Always Write Active Tool	False
Is Center Origin	False
Number of Extruders	1
Number of Extruders That Are Enabled	1
Outer Nozzle Diameter	1	mm
Nozzle Length	3	mm
Nozzle Angle	45	°
Heat Zone Length	16	mm
Enable Nozzle Temperature Control	True
Heat Up Speed	2	°C/s
Cool Down Speed	2	°C/s
Minimal Time Standby Temperature	50	s
G-code Flavor	Marlin
Firmware Retraction	False
Extruders Share Heater	False
Extruders Share Nozzle	False
Shared Nozzle Initial Retraction	0	mm
Disallowed Areas	[[[-117.5, 117.5], [-117.5, 108], [117.5, 108], [117.5, 117.5]], [[-117.5, -108], [-117.5, -117.5], [117.5, -117.5], [117.5, -108]]]
Nozzle Disallowed Areas	[]
Machine Head & Fan Polygon	[[-26, 34], [-26, -32], [32, -32], [32, 34]]
Gantry Height	25
Nozzle ID	unknown
Nozzle Diameter	0.4	mm
Offset with Extruder	True
Extruder Prime Z Position	0	mm
Absolute Extruder Prime Position	False
Maximum Speed X	500	mm/s
Maximum Speed Y	500	mm/s
Maximum Speed Z	10	mm/s
Maximum Feedrate	50	mm/s
Maximum Acceleration X	500	mm/s²
Maximum Acceleration Y	500	mm/s²
Maximum Acceleration Z	100	mm/s²
Maximum Filament Acceleration	5000	mm/s²
Default Acceleration	500	mm/s²
Default X-Y Jerk	10	mm/s
Default Z Jerk	0.4	mm/s
Default Filament Jerk	5	mm/s
Steps per Millimeter (X)	50
Steps per Millimeter (Y)	50
Steps per Millimeter (Z)	50
Steps per Millimeter (E)	1600
X Endstop in Positive Direction	False
Y Endstop in Positive Direction	False
Z Endstop in Positive Direction	True
Minimum Feedrate	0	mm/s
Feeder Wheel Diameter	10	mm
Extruder : 1 Machine
Extruder	0
Nozzle ID	unknown
Nozzle Diameter	0.4	mm
Nozzle X Offset	0	mm
Nozzle Y Offset	0	mm
Extruder Start G-Code
Extruder Start Position Absolute	False
Extruder Start Position X	0	mm
Extruder Start Position Y	0	mm
Extruder End G-Code
Extruder End Position Absolute	False
Extruder End Position X	0	mm
Extruder End Position Y	0	mm
Extruder Prime Z Position	0	mm
Extruder Print Cooling Fan	0